Crestron MC4 control system (este producto se cotiza por proyecto)

Provides a secure, high‑performance, cost-effective control system for use with Crestron Home® OS. A small form factor and low profile installation make it perfect for use in single‑room systems, small to medium‑sized homes, and MDUs (multidwelling units). Provides a built-in gateway for pairing infiNET EX® and ER wireless devices.

Wired Communications
Ethernet    100/1000 Mbps, autoswitching, autonegotiating, autodiscovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer Protocol), FIPS 140-2 compliant encryption, IPv4 or IPv6, HTTPS web server, SMTP email client
Cresnet® Network    Cresnet server mode1
USB    Supports USB mass storage class devices via the rear panel USB 2.0 host port
RS-232    For 2-way device control and monitoring, COM port supports RS‑232 up to 115.2k baud with software handshaking
IR    Supports 1‑way device control via infrared up to 1.2 MHz
BACnet™ network/IP    Supports up to 500 BACnet objects3
Wireless Communications1
RF Transceiver    infiNET EX® network 2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.5 MHz), default channel 15; IEEE 802.15.4 compliant
Range    50 ft (15 m) to nearest mesh network device(s), subject to site-specific conditions and individual device capabilities, range between floors or ceilings is limited to one level2
NOTE: Do not rack mount or stack multiple units when using wireless communications. Use care when positioning the device to avoid interference from nearby RF devices, obstructions, and metal surfaces.
Memory
SDRAM    2 GB
Flash    8 GB
Memory Card    Supports microSD® cards up to 32 GB (4 GB included)
External Storage    Supports USB mass storage devices up to 1 TB
Connectors and Card Slots
MEMORY    (1) microSD memory card slot;
Accepts one microSD card up to 32 GB for storage of log files;
4 GB microSD card included
G    (1) 6-32 screw;
Chassis ground lug
USB    (1) USB Type-A connector, female;
USB 2.0 port for storage devices
IR IN    (1) 3.5 mm TRS mini phone jack;
For connecting CNXRMIRD IR receiver;
Allows IR wireless control from Crestron and third‑party remotes using RC‑5 IR commands
RELAY (1–2)    (1) 4-pin 3.5 mm detachable terminal block;
Comprises (2) normally open, isolated relays;
Rated 1 Amp, 30 VAC/VDC;
MOV arc suppression across contacts
VER SI (1–2)    (1) 3-pin 3.5 mm detachable terminal block;
Comprises (2) Versiport digital input/output or analog input ports (referenced to GND);
Digital Input: Rated for 0–24VDC, input impedance 20k Ω, logic threshold >3.125V low/0 and <1.875V high/1;
Digital Output: 250 mA sink from maximum 24VDC, catch diodes for use with real world loads;
Analog Input: Rated for 0–10VDC, protected to 24VDC maximum, input impedance 21k Ω with pull-up resistor disabled;
Programmable 5V, 2k Ω pull-up resistor per pin
COM     (1) 3-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;
Up to 115.2k baud; software handshaking support
IR (1–4)    (2) 4-pin 3.5 mm detachable terminal blocks;
Comprises (4) IR output ports;
IR output up to 1.2 MHz;
4 IRP2 IR emitters included, additional emitters sold separately
EX/ER    (1) Connection for supplied antenna
CRESNET    (1) 4-pin 3.5 mm detachable terminal block;
Cresnet server port1;
Outputs power to Cresnet devices;
See "Power" section below for additional details
LAN    (1) 8-pin RJ-45 connector, female;
100BASE-T/1000BASE-TX Ethernet port;
PoE (Power over Ethernet) PD (Powered Device) port
Controls and Indicators
PWR    (1) Bicolor green/amber LED, indicates operating power is present;
Amber indicates that the device is booting and is not yet ready to operate;
Green indicates that the device is ready to operate
HW-R    (1) Recessed push button, initiates hardware reset
SW-R    (1) Recessed push button, initiates software reset
ACQUIRE    (1) Push button with red LED, used to set up connections with wireless devices
LAN    (1) Bicolor green/amber and (1) Amber LEDs;
Green/amber LED indicates Ethernet link status and connection speed;
Amber LED indicates Ethernet activity
Power
Power Source Options    PoE (Power over Ethernet)
Power over Ethernet    IEEE 802.3at Type 1 (802.3af compatible) Class 0 (12.95 W) PoE Powered Device
Available Cresnet Power    2.5 W
Power Consumption    7 W typical
Environmental
Temperature    41 to 113°F (5 to 45°C)
Humidity    10 to 90% (noncondensing)
Heat Dissipation    24 BTU/hr
Enclosure
Chassis    Metal, black finish, with (2) integral mounting flanges; vented top, sides, and bottom
Mounting    Freestanding, surface mount, attach to a single rack rail, or 1 RU 19‑in. rack mountable (rack ears included)
Dimensions
Height    1.07 in. (27 mm)
Width    10.15 in. (258 mm)
Depth    5.11 in. (130 mm)
Weight
1.0 lb (454 g)